Shop SoundAndVision
Refine By

Tonearms

  • Sort By:
Music Hall

carbon fiber tonearm. flexible internal tonearm wire drawn from high purity copper. counterweight's center of gravity is level wit...h the stylus tip. resonance damping counterweight is decoupled from the tonearm. read more

REGA

Features: RB303 tonearm Double brace technology Light weight plinth design 24v low noise low vibration hand tuned motor assembly

Pro-Ject
1,099.00
at Amazon.com

The Classic offers classic look and innovative high-end technology This turntable makes use of traditional frame design which was ...established by the famous turntable manufacturers of the 50's and 60's. It uses a compact simple and elegant form factor. The Classic incorporates a combination of approved belt drive design using a low noise AC motor with an ultra precision frequency DC-driven AC generator for ultimate speed stability. Advanced technology is used for decoupling and the completely new designed tonearm. PLATTER & SUB-PLATTER The heavy aluminium main platter construction utilises advanced thermo plastic elastomers (TPE*) for optimising resonance behaviour. A drawback for most of the old designs was the platter. Casted platters all have been heavy (which is good for speed constancy and low wow and flutter) but suffered very much from ringing effects which again caused colouration of the sound. The platter of The Classic is precisely machined out of a special aluminium alloy again damped with TPE*, which offers special damping abilities. The subplatter / main bearing construction we use is similar system as on the Debut. It is made of hardened steel/ Bronze bushing/ Teflon bearing mirror, which results in very smooth low noise running smoothness of the bearing. The main difference to the Debut bearing are the tolerances which are by factor 10 lower and therefore more precise (0,005%). Especially the subplatter is a very sophisticated part which is accurately machined and guarantees a very good isolation between bearing noise and the platter itself. The radical new designed Classic Tonearm is the result of 25 years of experience in mechanical construction. The tonearm tube is made out of a sandwich of Carbon and Aluminium: Carbon for stiffness and speed, Alu for better damping. The Cardan bearing assembly with pin-point Zircon bearing provides ultra low friction. read more

Pro-Ject

Precision machined tonearm bearing fine adjustment tool! Fits all Pro-Ject tonearms and allows qualified personnel to optimise bea...ring adjustment,when bearings are misadjusted, because of unassured transport of a turntable. If you are not sure about correct adjustment, please contact your local dealer! Suitable for all Pro-Ject tonearms Allows fine adjustment of bearings, if misadjusted Caution: for qualified personnel only Includes 2 inserts for different bearings Full metal (aluminium & brass) read more

Q UP

Q UP Tonearm Lifter Q UP Tonearm Lifter Adds Automatic Tonearm-Lift Functionality to Almost Any Manual Turntable: Never Worry Abou...t Remembering the Last Track on an LP With Convenient, Easy-to-Install Device Add automatic tonearm-lift functionality to almost any manual turntable with the Q UP tonearm lifter . Many 'tables require you to grab the tonearm at the end of a record, but we know this can be an inconvenience. Q UP takes any worries about having to remember the last track on an LP by picking up the tonearm and lifting the needle out of harm's way when a record finishes playing. Since it doesn't interact with the tonearm until the end the playing cycle, Q UP doesn't impact tonal balance or system performance. This trigger-and-lift design is easy to install and compatible with almost every 'tonearm on the market, independent of shape, thickness, or height. Awesome, and 100% Music Direct Guaranteed. Compatible With Almost All Bearing Tonearms Q UP can be used with most bearing tonearm types, from uni-pivot to gimbal. However, Q UP is not compatible with linear tracking arms. If you have a question about your particular setup, please contact Music Direct. Q UP requires a flat space near the tonearm with approximately 0.55" (14mm) of plinth space near the tonearm. The minimum height between the plinth and the bottom of the tonearm when playing a record is 1.42" (36mm). Most tonearms and turntables fit these criteria. NOTE: Pro-Ject Debut Series tonearms can use a Q UP without its base; all that's required is double-sided tape to affix the Q UP to the platform. Three Different-Sized Lifters Included With Q UP Variations in height between the plinth and the bottom of the tonearm are common, so Q UP includes three different-sized lifters: 10mm, 20mm, and 30mm. Easily affixed to the bottom of Q UP, these give Q UP great compatibility with a b read more

Sota

RUMBLE Less than -65db unweighted WOW & FLUTTER Less than .1% RMS (DIN 45-507) TRANSMISSION Belt drive SPEEDS 33-1/3 and 45 RPM WE...IGHT 18 lbs. (12 kg) DIMENSIONS 6" H, 18-1/4" W, 14-1/4 " D TONEARM: EFFECTIVE LENGTH 237mm OVERHANG 15mm OFFSET ANGLE 21.63 degrees CARTRIDGE WEIGHT RANGE 4 to 11 grams read more

Audiowood
1,399.99
at Amazon.com

Barky is a precision turntable that features a high-quality Rega parts kit, glass platter, RB303 arm and Rega Elys2 cartridge. Sol...id ash round is finished with polyurethane and paste wax, and has adjustable solid-brass spike feet. Barky is a limited-production (10-15 per year on average), high-quality turntable made with a solid ash round, quality Rega parts kit, 24 Volt Power Supply ($225 retail), heavy glass platter ($135 retail) and Rega RB303 tonearm ($595 retail). It includes a pre-mounted Rega Elys2 Cartridge ($295 retail, not shown), adjustable solid brass spike legs, and is finished with hand-rubbed polyurethane and paste wax. Each Barky is somewhat unique. Barky has been featured in Metropolitan Home, Zink, California Home and Design, Velvet (Italy), Daily Mail (UK) and in dozens of online design mags. and blogs, including BoingBoing, Uncrate, NotCot, DesignBoom, Gizmodo, etc. Barky is available in either 115V or 230V versions (please specify when ordering). Barky is also compatible with the Rega TTPSU external power supply which is available, and which allows for push-button speed changes. read more

Technics Original

Technics PAM18201K - 1200 Tonearm assembly Original Complete Tone Arm Assembly SL1200

REGA

Features: RB303 tonearm Double brace technology Light weight plinth design 24v low noise low vibration hand tuned motor assembly

Sota

RUMBLE Less than -65db unweighted WOW & FLUTTER Less than .1% RMS (DIN 45-507) TRANSMISSION Belt drive SPEEDS 33-1/3 and 45 RPM WE...IGHT 18 lbs. (12 kg) DIMENSIONS 6" H, 18-1/4" W, 14-1/4 " D TONEARM: EFFECTIVE LENGTH 237mm OVERHANG 15mm OFFSET ANGLE 21.63 degrees CARTRIDGE WEIGHT RANGE 4 to 11 grams read more