Onkyo PR-RZ5100 Surround Processor Review


Audio Performance
Features
Ergonomics
Value
PRICE $2,399

AT A GLANCE
Plus
Unimpeachable audio and basic video quality
Generally good ergonomic design
Eminently useful pop-up Quick Menu
Minus
No aptX for Bluetooth
Local-streaming audio doesn’t display file type/sampling info
Fairly downscaled remote

THE VERDICT
Onkyo’s latest A/V preamp/processor adds the Dolby Atmos/DTS:X and 4K/HDR capabilities needed to bring the brand’s pre/pro current, while maintaining very solid value in the field.

The A/V preamp/processors from Onkyo (and sister brand Integra) have been through five or six generations over the years, and I think I’ve tested or at least used just about all of them. And for that decade-plus span, my overall reaction to them has remained pretty consistent: all the A/V-system quarterbacking any rational being needs at a fair price. Onkyo’s latest iteration, the PR-RZ5100 network A/V controller, seems unlikely to change that conclusion while updating the series to 11.2-channel, 4K/HDR status.

As has been the case with previous generations, the PR-RZ5100 is more or less Onkyo’s flagship A/V receiver—in this case, the $3,299 TX-RZ3100—with the power amp section deleted in favor of pro-style XLR balanced-line audio outputs for all 11.2 channels. But I intend no asperity in pointing this out; Brand O’s top A/V receivers have long been among the highest performance/value options, and for those who prefer the flexibility and upgradeability of outboard amplification, the $900 savings likely seems eminently fair.

917onkrec.open.jpg

As with so many this-year’s-model A/V designs, the PR-RZ5100’s evolutions are mostly about two things: Dolby Atmos/DTS:X “objectbased” surround processing and 4K/HDR video. For the former, Onkyo deploys dual Analog Devices SHARC processors wielding an almost unbelievable 6 giga-operations per second (plus discrete 32-bit DACs all around). Meanwhile, its HDR video compatibility and 4K-ness are manifested by 4K/60 HDMI facilities with baked-in HDCP 2.2 copyright management, HDR passthrough (HDR10 now, Dolby Vision later with a promised firmware update), and BT.2020 and Deep Color support, all implemented by unnamed video processing. (Onkyo says 4K video and HDCP 2.2 are supported on only five of the eight HDMI 2.0a inputs and both the Main and Zone 2 HDMI outs; the remaining HDMI inputs are HDCP 1.4.) The pre/pro will scale 1080p (only) to 4K and will transcode analog composite video to component, but that’s about it for video processing. (This seems to be the trend among A/V gear makers today, driven no doubt by the fact that any 4K display will, by definition, have its own 4K scaling on board. This makes perfect sense to me, and the incidental cost savings is welcome.)

Features-wise, the Onkyo loads everything you might expect, including onboard Wi-Fi, with Chromecast built in (Google’s new name for Google Cast) and Apple AirPlay networking, Bluetooth, and a good range of streaming apps, such as Pandora, Spotify, and Tidal. For the rest, I’ll refer you to Onkyo’s website; there’s far too much to list here.

Cosmetically, the new pre/pro is a bit taller, and thus a bit boxierlooking, than previous generations. Its control arrangement of a single large knob and many small pushbuttons (with tiny on-key graphics) seems chosen more for appearances than for ergonomics, which is perfectly acceptable in a component whose interface, virtually always, will be via remote control and onscreen menus.

Setup
I installed the PR-RZ5100 in my long-term “B-chain,” comprising a 7 x 150-watt power amp and assorted-brand loudspeakers in a 5.1.4 Atmos configuration. (A compact 2 x 35-watt integrated amp drives my rear elevation channels, which works just fine in my room.) The Onkyo’s main HDMI output went to my 55-inch Vizio M Series 4K display, with source material arriving primarily from my Oppo BDP-105 player and occasionally from an Xfinity X1 cable box, which is crashing only about once a week these days.

917onkrec.bac.jpg

The actual installation was merely a matter of swapping cables—lots of them. While the PR-RZ5100 offers balanced XLR outputs on all 13 channels, my single-ended amps are RCA-in only, which is what I used. (As an aside, I don’t feel that a balanced-line connection’s potential virtue of lessening induced noise, which is real, is called for in about 97 percent of consumer setups; I’ve certainly never found it necessary in mine.)

With the wiring complete, I ran Onkyo’s AccuEQ auto calibration and room-correction system. (Like several other manufacturers, Onkyo has dropped Audyssey EQ in favor of their own proprietary, non-licensed, and presumably less costly option.) This required about 6 minutes of self-generated noise bursts and clicks from all channels in sequence, and it returned crossover settings that were all just about spot on at 40 hertz L/R, 80 Hz center, and 90 Hz surrounds, as well as distance and level results that were very close to what I expected. Center level was about a decibel high on my meter, but it’s rare for any auto-cal system to agree perfectly with another measurement method. So in all, I have to give AccuEQ’s setup acumen high marks.

The Onkyo system’s room/speaker-correction EQ can be applied to all channels, or to all minus the main front pair. With all channels corrected, I heard a very subtle sharpening of imaging and a tightening of lower midbass, such as typical pop/rock bass lines. This seemed more consistent than otherwise with what other systems, including both toptier Audyssey and Dirac, have accomplished in my room and setup. That said, it’s impossible for me to qualify the auto EQ here as better, worse, or the same without recourse to comparisons, which of course is impossible. Onkyo’s routine takes data from just one mic position, which would seem to be a limiting factor; but either way, results from one run on one system in one room have to be noted as interesting but absolutely not definitive. As is my custom, I did all of my serious listening with the auto EQ defeated on all channels.

Listening and Viewing
Disappointingly, I have very little to say about the PR-RZ5100’s sound quality, except that my system sounded great on everything I played from it. (If you’re looking for judgments about how one particular, competently engineered line-level audio component sounds “more tuneful” or “tighter resolving of midfield image depth” than another, you’ve got the wrong guy.) The Onkyo decodes and plays DSD audio up to 11.2 megahertz, and my limited but growing library produced all the virtues I expected. For one example, a DSD download of an obscure but fascinating Villa-Lobos piece, the Concerto for Bassoon and Low Strings, had all the delicacy and detail required for highly persuasive naturalism. (And as a bassoonist in recovery, I should know.)

COMPANY INFO
Onkyo
ARTICLE CONTENTS

COMMENTS
drny's picture

S&V, you well know the dirty little secret that HDMI 2.1 will make all AVRs as well as most Integrated Amps and Sound Processors obsolete.
I have not updated (and will not update) my 2016 Yamaha AVR based solely on the fact that all brands and models will be made obsolete by 2019 (or earlier) adoption of HDMI 2.1 connection (new cables as well will be required.
As such I don't sent any video signal through my AVR. Only Audio goes to my Receiver.
I will wait till 2019 to update / upgrade. That's when HDMI 2.1 with necessary firmware updates will have proliferated the AVR market.
By the way the same goes for Smart TVs.
I own a Samsung JS9500 (2015 model year). No matter how much I feel tempted to jump into the OLED pool, I will stand by until 2019 model year models(with late season firmware update).
Just as with AVR the change to HDMI 2.1 will eventually make $3000-7000 TV displays obsolete.

mountainman3520's picture

Hello. Anyone have test results of whether this generation of Onkyo prepro uses mechanical relays to change between modes?
I spent over a year trying to resolve this on a top end Onkyo prepro from a few years ago (PRS-5507 was the number if I recall). I also tested the following year's model in a store and it had the same design defect.
The issue was that changes between digital audio stream formats caused a mechanical relay to make a loud CLICK noise. This wouldn't have been such a problem if it only occurred during infrequent user selected mode changes, but ANY brief interruption of the digital audio stream caused an automatic CLICK into "no audio" mode followed by another CLICK back into active audio. So every time a source device with digital audio was interrupted, such as a streamed program, TV show on a DVR, Netflix video, etc being paused or skipped forward/back, or any change, it would result in a sequence of audible clicks. Skipping 3 minutes of commercials in six 30 second remote button pushes? CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK CLICK. Ugh!
Many people reported the issue on various forums. A few said they were able to resolve it by adjusting programmable default sound source settings and Onkyo told me this as well. But I followed their instructions and they did not resolve the issue. Eventually Onkyo issued a firmware change that they claimed would fix it, but it also did not work.
Pretty much ruined my enjoyment of that Onkyo prepro despite its other merits. If my AV gear was in a different room it wouldn't be an issue. Or a sealed rack, but then it would have cooked.
I'm curious if this lameness has been resolved after a few years and models.

katherinerose6's picture

I noticed that my meter's center level was a few decibels above normal, but it's not common for an office demolition auto-cal system to precisely match up with another measurement technique.

aasik90's picture

Thank you for sharing such a useful article, defiantly i will share to my friends and WhatsApp groups -

Dubai Free Zone Company Setup

best seo expert abu dhabi

SEO freelancer near me

X